CertBus 2020 Newest Cisco 200-105 Cisco Certified Network Associate Exam VCE and PDF Dumps for Free Download!

☆ 200-105 Cisco Certified Network Associate Exam PDF and VCE Dumps : 709QAs Instant Download: https://www.certgod.com/200-105.html [100% 200-105 Exam Pass Guaranteed or Money Refund!!]
☆ Free view online pdf on CertBus free test 200-105 PDF: https://www.certgod.com/online-pdf/200-105.pdf
☆ CertBus 2020 Newest 200-105 Cisco Certified Network Associate exam Question PDF Free Download from Google Drive Share: https://drive.google.com/file/d/0B_3QX8HGRR1mdlhPS1BHSTlidlU/view?usp=sharing

Following 200-105 709QAs are all new published by Cisco Official Exam Center

This dump is 100% valid to pass Cisco Cisco Certified Network Associate Jul 08,2020 Newest 200-105 free download exam. The only tips is please do not just memorize the questions and answers, you need to get through understanding of it because the question changed a little in the real exam. Follow the instructions in the CertBus Cisco Certified Network Associate Newest 200-105 pdf dumps Interconnecting Cisco Networking Devices Part 2 PDF and VCEs. All CertBus materials will help you pass your Cisco Cisco Certified Network Associate exam successfully.

CertBus – help you to get your 200-105 certification more easily. save your time and money! high pass rate! 200-105 certification – 200-105 certifications. pass your 200-105 exam in 1 day with CertBus. CertBus – most reliable and professional 200-105 certification exam material provider. real latest, easily pass.

We CertBus has our own expert team. They selected and published the latest 200-105 preparation materials from Cisco Official Exam-Center: https://www.certgod.com/200-105.html

Question 1:

Under normal operations, Cisco recommends that you configure switchports on which VLAN?

A. on any VLAN except the default VLAN

B. on the management VLAN

C. on the native VLAN

D. on the default VLAN

Correct Answer: D

Question 2:

Which three describe the reasons large OSPF networks use a hierarchical design? (Choose Three) A. to speed up convergence

B. to reduce routing overhead

C. to lower costs by replacing routers with distribution layer switches.

D. to decrease latency by increasing bandwidth.

E. to confine network instability to single areas of the network.

F. to reduce the complexity of router configuration.

Correct Answer: ABE

Question 3:

A security administrator wants to profile endpoints and gain visibility into attempted authentications. Which 802.1x mode allows these actions?

A. Monitor mode

B. High-Security mode

C. Low-impact mode

D. Closed mode

Correct Answer: A

Question 4:

Which value can you modify to configure a specific interface as the preferred forwarding interface?

A. The interface number

B. The port priority

C. The VLAN priority

D. The hello time

Correct Answer: B

Question 5:

The company internetwork is subnetted using 29 bits. Which wildcard mask should be used to configure an extended access list to permit or deny access to an entire subnetwork?

A. 255.255.255.224

B. 255.255.255.248

C. 0.0.0.224

D. 0.0.0.8

E. 0.0.0.7

F. 0.0.0.3

Correct Answer: E

200-105 VCE Dumps200-105 Practice Test200-105 Braindumps

Question 6:

A network administrator receives an error message while trying to configure the Ethernet interface of a router with IP address 10.24.24.24/29. Which statement explains the reason for this issue?

A. VLSM-capable routing protocols must be enabled first on the router.

B. This address is a network address.

C. This address is a broadcast address.

D. The Ethernet interface is faulty.

Correct Answer: B

Question 7:

Which two are features of IPv6? (Choose two.)

A. anycast

B. broadcast

C. multicast

D. podcast

E. allcast

Correct Answer: AC

Question 8:

It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit. Which of the following are required to solve this? (Choose three)

A. configure static frame relay map entries for each subinterface network.

B. remove the ip address from the physical interface

C. create the virtual interfaces with the interface command

D. configure each subinterface with its own IP address

E. disable split horizon to prevent routing loops between the subinterface networks

F. encapsulate the physical interface with multipoint PPP

Correct Answer: BCD

http://www.orbit-computer-solutions.com/How-To-Configure-Frame-Relay-Subinterfaces.php Step to configure Frame Relay subinterfaces on a physical interface:

1.

Remove any network layer address (IP) assigned to the physical interface. If the physical interface has an address, frames are not received by the local subinterfaces.

2.

Configure Frame Relay encapsulation on the physical interface using the encapsulation frame- relay command.

3.

For each of the defined PVCs, create a logical subinterface. Specify the port number, followed by a period (.) and the subinterface number. To make troubleshooting easier, it is suggested that the subinterface number matches the DLCI number.

4.

Configure an IP address for the interface and set the bandwidth.

5.

Configure the local DLCI on the subinterface using the frame-relay interface-dlci command. Configuration Example:

R1>enable R1#configure terminal R1(config)#interface serial 0/0/0 R1(config-if)#no ip address R1(config-if)#encapsulation frame-relay R1(config-if)#no shutdown R1(config-if)#exit R1(config-subif)#interface serial 0/0/0.102 point-to-point R1(config-subif)#ip address 192.168.1.245 255.255.255.252 R1(config-subif)#frame-relay interface-dlci 102 R1(config-subif)#end R1#copy running-config startup-config

Question 9:

Two switches are connected through a trunk link. Which two commands show that there is a native VLAN mismatch on that link? (Choose two.)

A. show vlan brief

B. show interface trunk

C. show interface vlan

D. show interface switchport

E. show interface interface

F. show switchport trunk

Correct Answer: BD

Question 10:

Which port state is introduced by Rapid-PVST?

A. learning

B. listening

C. discarding

D. forwarding

Correct Answer: C

Spanning Tree from PVST to Rapid-PVST Migration Configuration Example Reference 1: http://www.cisco.com/en/US/products/hw/switches/ps708/products_configuration_example09186a00807b0670.shtml Reference 2: http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml PVST is based on IEEE802.1D Spanning Tree Protocol (STP). But PVST has only 3 port states (discarding, learning and forwarding) while STP has 5 port states (blocking, listening, learning, forwarding and disabled). So discarding is a new port state in PVST .

Background Information

802.1D Spanning Tree Protocol (STP) has a drawback of slow convergence. Cisco Catalyst switches support three types of STPs, which are PVST , rapid-PVST and MST. PVST is based on IEEE802.1D standard and includes Cisco

proprietary extensions such as BackboneFast, UplinkFast, and PortFast. Rapid-PVST is based on IEEE 802.1w standard and has a faster convergence than 802.1D. RSTP (IEEE 802.1w) natively includes most of the Cisco proprietary

enhancements to the 802.1D Spanning Tree, such as BackboneFast and UplinkFast. Rapid-PVST has these unique features:

Uses Bridge Protocol Data Unit (BPDU) version 2 which is backward compatible with the 802.1D STP, which uses BPDU version 0.

All the switches generate BPDUs and send out on all the ports every 2 seconds, whereas in 802.1D STP only the root bridge sends the configuration BPDUs.

Port Roles–Root port, designated port, alternate port and backup port.

Port States–Discarding, Learning, and Forwarding.

Port Types–Edge Port (PortFast), Point-to-Point and Shared port.

Rapid-PVST uses RSTP to provide faster convergence. When any RSTP port receives legacy 802.1D BPDU, it falls back to legacy STP and the inherent fast convergence benefits of 802.1w are lost when it interacts with legacy bridges.

CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 200-105 exam successfully with our Cisco materials. CertBus Interconnecting Cisco Networking Devices Part 2 exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus Interconnecting Cisco Networking Devices Part 2 exam questions and answers are the most valid. CertBus exam Interconnecting Cisco Networking Devices Part 2 exam dumps will help you to be the Cisco specialist, clear your 200-105 exam and get the final success.

200-105 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mdlhPS1BHSTlidlU/view?usp=sharing

200-105 Cisco exam dumps (100% Pass Guaranteed) from CertBus: https://www.certgod.com/200-105.html [100% Exam Pass Guaranteed]

Why select/choose CertBus?

Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.

Brand	Certbus	Testking	Pass4sure	Actualtests	Others
Price	$45.99	$124.99	$125.99	$189	$69.99-99.99
Up-to-Date Dumps
Free 365 Days Update
Real Questions
Printable PDF
Test Engine
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back
Secure Payment
Privacy Protection