CertBus 2018 Valid Cisco 400-101 CCIE Exam VCE and PDF Dumps for Free Download!
☆ 400-101 CCIE Exam PDF and VCE Dumps : 1379QAs Instant Download: https://www.certgod.com/400-101.html [100% 400-101 Exam Pass Guaranteed or Money Refund!!]
☆ Free view online pdf on CertBus free test 400-101 PDF: https://www.certgod.com/online-pdf/400-101.pdf
☆ CertBus 2018 Valid 400-101 CCIE exam Question PDF Free Download from Google Drive Share: https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing
Following 400-101 1379QAs are all new published by Cisco Official Exam Center
Do not worry about your CCIE Latest 400-101 vce exam preparation? Hand over your problems to CertBus in change of the CCIE Latest 400-101 study guide CCIE Routing and Switching Written v5.0 certifications! CertBus provides the latest Cisco CCIE Aug 29,2018 Newest 400-101 practice exam preparation materials with PDF and VCEs. We CertBus guarantees you passing CCIE Hotest 400-101 QAs exam for sure.
CertBus exam guide: pass the 400-101 exam on your first attempt! CertBus 100% real 400-101 certification exam questions and answers. easily pass with a high score. pass 400-101 certification exam with CertBus braindumps! CertBus- reliable 400-101 certifications expert on 400-101 exam study guide providing. CertBus – leading provider on all 400-101 certification real exam practice and test questions and answers.
We CertBus has our own expert team. They selected and published the latest 400-101 preparation materials from Cisco Official Exam-Center: https://www.certgod.com/400-101.html
QUESTION NO:2
A branch router is configured with an egress QoS policy that was designed for a total number of
10 concurrent VOIP calls.
Due to expansion, 15 VOIP calls are now running over the link, but after the 14th call was
established, all calls were affected and the voice quality was dramatically degraded.
Assuming that there is enough bandwidth on the link for all of this traffic, which part of the QoS
configuration should be updated due to the new traffic profile?
A. Increase the shaping rate for the priority queue. B.
Remove the policer applied on the priority queue. C.
Remove the shaper applied on the priority queue. D.
Increase the policing rate for the priority queue.
Answer: D
Explanation:
QUESTION NO:3
A new backup connection is being deployed on a remote site router. The stability of the connection
has been a concern. In order to provide more information to EIGRP regarding this interface, you
wish to incorporate the “reliability” cost metric in the EIGRP calculation with the command metric
weights 1 0 1 0 1.
What impact will this modification on the remote site router have for other existing EIGRP
neighborships from the same EIGRP domain?
A. Existing neighbors will immediately begin using the new metric.
B. Existing neighbors will use the new metric after clearing the EIGRP neighbors.
C. Existing neighbors will resync, maintaining the neighbor relationship.
D. All existing neighbor relationships will go down.
Answer: D
Explanation:
QUESTION NO:4
Refer to the exhibit.
R1 has an EBGP session to ISP 1 and an EBGP session to ISP 2. R1 receives the same prefixes
through both links.
Which configuration should be applied so that the link between R1 and ISP 2 will be preferred for
outgoing traffic (R1 to ISP 2)?
A. Increase local preference on R1 for received routes
B. Decrease local preference on R1 for received routes
C. Increase MED on ISP 2 for received routes
D. Decrease MED on ISP 2 for received routes
Answer: A
Explanation: Explanation
Local preference is an indication to the AS about which path has preference to exit the AS in order
to reach a certain network. A path with higher local preference is preferred more. The default value
of preference is 100.
Reference
http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080b82d1f.s
html?
referring_site=smartnavRD
QUESTION NO:13
Which two statements are true about traffic shaping? (Choose two.)
A. Out-of-profile packets are queued.
B. It causes TCP retransmits.
C. Marking/remarking is not supported.
D. It does not respond to BECN and ForeSight Messages.
E. It uses a single/two-bucket mechanism for metering.
Answer: A,C
Explanation:
QUESTION NO:14
Which three options are features of VTP version 3? (Choose three.)
A. VTPv3 supports 8K VLANs.
B. VTPv3 supports private VLAN mapping.
C. VTPv3 allows for domain discovery.
D. VTPv3 uses a primary server concept to avoid configuration revision issues.
E. VTPv3 is not compatible with VTPv1 or VTPv2.
F. VTPv3 has a hidden password option.
Answer: B,D,F
Explanation:
Key Benefits of VTP Version 3
Much work has gone into improving the usability of VTP version 3 in three major areas:
The new version of VTP offers better administrative control over which device is allowed to update
other devices\’ view of the VLAN topology. The chance of unintended and disruptive changes is
significantly reduced, and availability is increased. The reduced risk of unintended changes will
ease the change process and help speed deployment.
Functionality for the VLAN environment has been significantly expanded. Two enhancements are
most beneficial for today\’s networks:
400-101 VCE Dumps400-101 Practice Test400-101 Exam Questions
QUESTION NO:16
In 802.1s, how is the VLAN to instance mapping represented in the BPDU?
A. The VLAN to instance mapping is a normal 16-byte field in the MST BPDU.
B. The VLAN to instance mapping is a normal 12-byte field in the MST BPDU.
C. The VLAN to instance mapping is a 16-byte MD5 signature field in the MST BPDU.
D. The VLAN to instance mapping is a 12-byte MD5 signature field in the MST BPDU.
Answer: C
Explanation:
MST Configuration and MST Region
Each switch running MST in the network has a single MST configuration that consists of these
three attributes:
1. An alphanumeric configuration name (32 bytes)
2. A configuration revision number (two bytes)
3. A 4096-element table that associates each of the potential 4096 VLANs supported on the
chassis to a given instance.
In order to be part of a common MST region, a group of switches must share the same
configuration attributes.
It is up to the network administrator to properly propagate the configuration throughout the region.
Currently, this step is only possible by the means of the command line interface (CLI) or through
Simple Network
Management Protocol (SNMP). Other methods can be envisioned, as the IEEE specification does
not explicitly mention how to accomplish that step.
Note: If for any reason two switches differ on one or more configuration attribute, the switches are
part of different regions. For more information refer to the Region Boundary section of this
document.
Region Boundary
In order to ensure consistent VLAN-to-instance mapping, it is necessary for the protocol to be able
to exactly identify the boundaries of the regions. For that purpose, the characteristics of the region
are included in the BPDUs. The exact VLANs-to-instance mapping is not propagated in the BPDU,
because the switches only need to know whether they are in the same region as a neighbor.
Therefore, only a digest of the VLANs-toinstance mapping table is sent, along with the revision
number and the name. Once a switch receives a BPDU, the switch extracts the digest (a
numerical value derived from the VLAN-to-instance mapping table through a mathematical
function) and compares this digest with its own computed digest. If the digests differ, the port on
which the BPDU was received is at the boundary of a region.
In generic terms, a port is at the boundary of a region if the designated bridge on its segment is in
a different region or if it receives legacy 802.1d BPDUs. In this diagram, the port on B1 is at the
boundary of region A, whereas the ports on B2 and B3 are internal to region B:
MST Instances
According to the IEEE 802.1s specification, an MST bridge must be able to handle at least these
two instances:
One Internal Spanning Tree (IST)
One or more Multiple Spanning Tree Instance(s) (MSTIs)
The terminology continues to evolve, as 802.1s is actually in a pre-standard phase. It is likely
these names will change in the final release of 802.1s. The Cisco implementation supports 16
instances: one IST (instance 0) and 15 MSTIs.
show vtp status
Cisco switches “show vtp status” Field Descriptions has a MD5 digest field that is a 16-byte
checksum of the
VTP configuration as shown below
Router# show vtp status
VTP Version: 3 (capable)
Configuration Revision: 1
Maximum VLANs supported locally: 1005
Number of existing VLANs: 37
VTP Operating Mode: Server
VTP Domain Name: [smartports]
VTP Pruning Mode: Disabled
VTP V2 Mode: Enabled
VTP Traps Generation: Disabled
MD5 digest : 0x26 0xEE 0x0D 0x84 0x73 0x0E 0x1B 0x69
Configuration last modified by 172.20.52.19 at 7-25-08 14:33:43
Local updater ID is 172.20.52.19 on interface Gi5/2 (first layer3 interface fou)
VTP version running: 2
Reference
http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfc.shtml
http://www.cisco.com/en/US/docs/ios-xml/ios/lanswitch/command/lsw-cr-book.pdf
QUESTION NO:24
Refer to the exhibit.
R1 is not learning about the 172.16.10.0 subnet from the BGP neighbor R2 (209.165.202.130).
What can be done so that R1 will learn about this network?
A. Disable auto-summary on R2.
B. Configure an explicit network command for the 172.16.10.0 subnet on R2.
C. Subnet information cannot be passed between IBGP peers.
D. Disable auto-summary on R1.
Answer: B
Explanation:
By default, BGP does not accept subnets redistributed from IGP. To advertise and carry subnet
routes in BGP, use an explicit network command or the no auto-summary command. If you disable
auto-summarization and have not entered a network command, you will not advertise network
routes for networks with subnet routes unless they contain a summary route.
Reference
http://www.cisco.com/en/US/docs/ios/11_3/np1/command/reference/1rbgp.html
QUESTION NO:25
Refer to the exhibit.
After a link flap in the network, which two EIGRP neighbors will not be queried for alternative
paths? (Choose two.)
A. 192.168.1.1
B. 192.168.3.7
C. 192.168.3.8
D. 192.168.3.6
E. 192.168.2.1
F. 192.168.3.9
Answer: B,C
Explanation:
Explanation
Both 192.168.3.7 and 192.168.3.8 are in an EIGRP Stub area
The Enhanced Interior Gateway Routing Protocol (EIGRP) Stub Routing feature improves network
stability, reduces resource utilization, and simplifies stub router configuration.
Stub routing is commonly used in a hub and spoke network topology. In a hub and spoke network,
one or more end (stub) networks are connected to a remote router (the spoke) that is connected to
one or more distribution routers (the hub). The remote router is adjacent only to one or more
distribution routers. The only route for IP traffic to follow into the remote router is through a
distribution router. This type of configuration is commonly used in WAN topologies where the
distribution router is directly connected to a WAN. The distribution router can be connected to
many more remote routers. Often, the distribution router will be connected to 100 or more remote
routers. In a hub and spoke topology, the remote router must forward all nonlocal traffic to a
distribution router, so it becomes unnecessary for the remote router to hold a complete routing
table. Generally, the distribution router need not send anything more than a default route to the
remote router.
When using the EIGRP Stub Routing feature, you need to configure the distribution and remote
routers to use EIGRP, and to configure only the remote router as a stub. Only specified routes are
propagated from the remote (stub) router. The router responds to queries for summaries,
connected routes, redistributed static routes, external routes, and internal routes with the message
“inaccessible.” A router that is configured as a stub will send a special peer information packet to
all neighboring routers to report its status as a stub router. Any neighbor that receives a packet
informing it of the stub status will not query the stub router for any routes, and a router that has a
stub peer will not query that peer. The stub router will depend on the distribution router to send the
proper updates to all peers.
Reference
http://www.cisco.com/en/US/docs/ios/12_0s/feature/guide/eigrpstb.html#wp1021949
QUESTION NO:36
For which routes does LDP advertise a label binding?
A. all routes in the routing table
B. only the IGP and BGP routes in the routing table
C. only the BGP routes in the routing table
D. only the IGP routes in the routing table
Answer: D
Explanation:
QUESTION NO:44
How is RPF used in multicast routing?
A. to prevent multicast packets from looping
B. to prevent PIM packets from looping
C. to instruct PIM where to send a (*, G) or (S, G) join message
D. to prevent multicast packets from looping and to instruct PIM where to send a (*, G) or (S, G)
join message
Answer: D
Explanation:
CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 400-101 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written v5.0 exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written v5.0 exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written v5.0 exam dumps will help you to be the Cisco specialist, clear your 400-101 exam and get the final success.
400-101 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing
400-101 Cisco exam dumps (100% Pass Guaranteed) from CertBus: https://www.certgod.com/400-101.html [100% Exam Pass Guaranteed]
Why select/choose CertBus?
Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.