CertBus 2018 Latest Cisco 400-101 CCIE Exam VCE and PDF Dumps for Free Download!
☆ 400-101 CCIE Exam PDF and VCE Dumps : 1379QAs Instant Download: https://www.certgod.com/400-101.html [100% 400-101 Exam Pass Guaranteed or Money Refund!!]
☆ Free view online pdf on CertBus free test 400-101 PDF: https://www.certgod.com/online-pdf/400-101.pdf
☆ CertBus 2018 Latest 400-101 CCIE exam Question PDF Free Download from Google Drive Share: https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing
Following 400-101 1379QAs are all new published by Cisco Official Exam Center
Do not worry about that if you are stuck in the CCIE Latest 400-101 practice exam difficulties, CertBus will assist you all your way through the CCIE Aug 24,2018 Newest 400-101 vce dumps CCIE Routing and Switching Written v5.0 exam with the most update CCIE Newest 400-101 pdf dumps PDF and VCE dumps. CertBus exam Newest 400-101 free download preparation materials are the most comprehensive material, covering every key knowledge of Latest 400-101 practice CCIE Routing and Switching Written v5.0 exam.
pass 400-101 test with CertBus practice exam questions. CertBus – clear all your 400-101 certification exams with CertBus study guide. 100% pass rate and money back guarantee. CertBus braindumps CertBus dumps free download. pass 400-101 certification exam with CertBus braindumps! CertBus – leading provider of latest 400-101 certification exam study materials. try to download the free demo.
We CertBus has our own expert team. They selected and published the latest 400-101 preparation materials from Cisco Official Exam-Center: https://www.certgod.com/400-101.html
QUESTION NO:2
A branch router is configured with an egress QoS policy that was designed for a total number of
10 concurrent VOIP calls.
Due to expansion, 15 VOIP calls are now running over the link, but after the 14th call was
established, all calls were affected and the voice quality was dramatically degraded.
Assuming that there is enough bandwidth on the link for all of this traffic, which part of the QoS
configuration should be updated due to the new traffic profile?
A. Increase the shaping rate for the priority queue. B.
Remove the policer applied on the priority queue. C.
Remove the shaper applied on the priority queue. D.
Increase the policing rate for the priority queue.
Answer: D
Explanation:
QUESTION NO:7
Which statement is true about TCN propagation?
A. The originator of the TCN immediately floods this information through the network.
B. The TCN propagation is a two step process.
C. A TCN is generated and sent to the root bridge.
D. The root bridge must flood this information throughout the network.
Answer: C
Explanation:
Explanation
New Topology Change Mechanisms
When an 802.1D bridge detects a topology change, it uses a reliable mechanism to first notify the
root bridge.
This is shown in this diagram:
Once the root bridge is aware of a change in the topology of the network, it sets the TC flag on the
BPDUs it sends out, which are then relayed to all the bridges in the network. When a bridge
receives a BPDU with the TC flag bit set, it reduces its bridging-table aging time to forward delay
seconds. This ensures a relatively quick flush of stale information. Refer to Understanding
Spanning-Tree Protocol Topology Changes for more information on this process. This topology
change mechanism is deeply remodeled in RSTP. Both the detection of a topology change and its
propagation through the network evolve.
Topology Change Detection
In RSTP, only non-edge ports that move to the forwarding state cause a topology change. This
means that a loss of connectivity is not considered as a topology change any more, contrary to
802.1D (that is, a port that moves to blocking no longer generates a TC). When a RSTP bridge
detects a topology change, these occur:
It starts the TC While timer with a value equal to twice the hello-time for all its non-edge
designated ports and its root port, if necessary.
It flushes the MAC addresses associated with all these ports.
Note: As long as the TC While timer runs on a port, the BPDUs sent out of that port have the TC
bit set.
BPDUs are also sent on the root port while the timer is active.
Topology Change Propagation
When a bridge receives a BPDU with the TC bit set from a neighbor, these occur:
It clears the MAC addresses learned on all its ports, except the one that receives the topology
change.
It starts the TC While timer and sends BPDUs with TC set on all its designated ports and root port
(RSTP no longer uses the specific TCN BPDU, unless a legacy bridge needs to be notified).
This way, the TCN floods very quickly across the whole network. The TC propagation is now a one
step process. In fact, the initiator of the topology change floods this information throughout the
network, as opposed to 802.1D where only the root did. This mechanism is much faster than the
802.1D equivalent. There is no need to wait for the root bridge to be notified and then maintain the
topology change state for the whole network for seconds.
In just a few seconds, or a small multiple of hello-times, most of the entries in the CAM tables of
the entire network (VLAN) flush. This approach results in potentially more temporary flooding, but
on the other hand it clears potential stale information that prevents rapid connectivity restitution.
Reference
http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml
QUESTION NO:9
Which two are effects of connecting a network segment that is running 802.1D to a network
segment that is running 802.1w? (Choose two.)
A. The entire network switches to 802.1D and generates BPDUs to determine root bridge status. B.
A migration delay of three seconds occurs when the port that is connected to the 802.1D bridge
comes up.
C. The entire network reconverges and a unique root bridge for the 802.1D segment, and a root
bridge for the 802.1w segment, is chosen.
D. The first hop 802.1w switch that is connected to the 802.1D runs entirely in 802.1D compatibility
mode and converts the BPDUs to either 802.1D or 802.1w BPDUs to the 802.1D or 802.1w
segments of the network.
E. Classic 802.1D timers, such as forward delay and max-age, will only be used as a backup, and
will not be necessary if point-to-point links and edge ports are properly identified and set by the
administrator.
Answer: B,E
Explanation:
Each port maintains a variable that defines the protocol to run on the corresponding segment. A
migration delay timer of three seconds also starts when the port comes up. When this timer runs,
the current STP or RSTP mode associated to the port is locked. As soon as the migration delay
expires, the port adapts to the mode that corresponds to the next BPDU it receives. If the port
changes its mode of operation as a result of a BPDU received, the migration delay restarts.
802.1D works by the concept that the protocol had to wait for the network to converge before it
transitioned a port into the forwarding state. With Rapid Spanning Tree it does not have to rely on
any timers, the only variables that that it relies on is edge ports and link types.
Any uplink port that has an alternate port to the root can be directly placed into the forwarding
state (This is the Rapid convergence that you speak of “restored quickly when RSTP is already in
use?”). This is what happened when you disconnected the primary look; the port that was ALT,
moved to FWD immediately, but the switch also still needs to create a BDU with the TC bit set to
notify the rest of the network that a topology has occurred and all non-edge designated ports will
transition to BLK, LRN, and then FWD to ensure there are no loops in the rest of the network. This
is why if you have a host on a switchport, and you know for a fact that it is only one host, enable
portfast to configure the port as an edgeport so that it does not have to transition to all the STP
states.
Reference
http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml
QUESTION NO:11
When you are troubleshooting duplex mismatches, which two errors are typically seen on the full-
duplex end? (Choose two.)
A. runts
B. FCS errors
C. interface resets
D. late collisions
Answer: A,B
Explanation:
QUESTION NO:13
Which two statements are true about traffic shaping? (Choose two.)
A. Out-of-profile packets are queued.
B. It causes TCP retransmits.
C. Marking/remarking is not supported.
D. It does not respond to BECN and ForeSight Messages.
E. It uses a single/two-bucket mechanism for metering.
Answer: A,C
Explanation:
Latest 400-101 Dumps400-101 PDF Dumps400-101 Practice Test
QUESTION NO:15
Which three options are considered in the spanning-tree decision process? (Choose three.)
A. lowest root bridge ID
B. lowest path cost to root bridge
C. lowest sender bridge ID
D. highest port ID
E. highest root bridge ID
F. highest path cost to root bridge
Answer: A,B,C
Explanation:
Configuration bridge protocol data units (BPDUs) are sent between switches for each port.
Switches use s four step process to save a copy of the best BPDU seen on every port. When a
port receives a better BPDU, it stops sending them. If the BPDUs stop arriving for 20 seconds
(default), it begins sending them again.
Step 1 Lowest Root Bridge ID (BID)
Step 2 Lowest Path Cost to Root Bridge
Step 3 Lowest Sender BID
Step 4 Lowest Port ID
Reference
Cisco General Networking Theory Quick Reference Sheets
QUESTION NO:21
Refer to the exhibit.
A packet from RTD with destination RTG, is reaching RTB. What is the path this packet will take
from RTB to reach RTG?
A. RTB – RTA – RTG
B. RTB – RTD – RTC – RTA – RTG
C. RTB – RTF – RTE – RTA – RTG
D. RTB will not be able to reach RTG since the OSPF configuration is wrong.
Answer: C
Explanation:
QUESTION NO:22
Refer to the exhibit.
Which path is selected as best path?
A. path 1, because it is learned from IGP B.
path 1, because the metric is the lowest C.
path 2, because it is external
D. path 2, because it has the higher router ID
Answer: B
Explanation:
QUESTION NO:24
Refer to the exhibit.
R1 is not learning about the 172.16.10.0 subnet from the BGP neighbor R2 (209.165.202.130).
What can be done so that R1 will learn about this network?
A. Disable auto-summary on R2.
B. Configure an explicit network command for the 172.16.10.0 subnet on R2.
C. Subnet information cannot be passed between IBGP peers.
D. Disable auto-summary on R1.
Answer: B
Explanation:
By default, BGP does not accept subnets redistributed from IGP. To advertise and carry subnet
routes in BGP, use an explicit network command or the no auto-summary command. If you disable
auto-summarization and have not entered a network command, you will not advertise network
routes for networks with subnet routes unless they contain a summary route.
Reference
http://www.cisco.com/en/US/docs/ios/11_3/np1/command/reference/1rbgp.html
QUESTION NO:25
Refer to the exhibit.
After a link flap in the network, which two EIGRP neighbors will not be queried for alternative
paths? (Choose two.)
A. 192.168.1.1
B. 192.168.3.7
C. 192.168.3.8
D. 192.168.3.6
E. 192.168.2.1
F. 192.168.3.9
Answer: B,C
Explanation:
Explanation
Both 192.168.3.7 and 192.168.3.8 are in an EIGRP Stub area
The Enhanced Interior Gateway Routing Protocol (EIGRP) Stub Routing feature improves network
stability, reduces resource utilization, and simplifies stub router configuration.
Stub routing is commonly used in a hub and spoke network topology. In a hub and spoke network,
one or more end (stub) networks are connected to a remote router (the spoke) that is connected to
one or more distribution routers (the hub). The remote router is adjacent only to one or more
distribution routers. The only route for IP traffic to follow into the remote router is through a
distribution router. This type of configuration is commonly used in WAN topologies where the
distribution router is directly connected to a WAN. The distribution router can be connected to
many more remote routers. Often, the distribution router will be connected to 100 or more remote
routers. In a hub and spoke topology, the remote router must forward all nonlocal traffic to a
distribution router, so it becomes unnecessary for the remote router to hold a complete routing
table. Generally, the distribution router need not send anything more than a default route to the
remote router.
When using the EIGRP Stub Routing feature, you need to configure the distribution and remote
routers to use EIGRP, and to configure only the remote router as a stub. Only specified routes are
propagated from the remote (stub) router. The router responds to queries for summaries,
connected routes, redistributed static routes, external routes, and internal routes with the message
“inaccessible.” A router that is configured as a stub will send a special peer information packet to
all neighboring routers to report its status as a stub router. Any neighbor that receives a packet
informing it of the stub status will not query the stub router for any routes, and a router that has a
stub peer will not query that peer. The stub router will depend on the distribution router to send the
proper updates to all peers.
Reference
http://www.cisco.com/en/US/docs/ios/12_0s/feature/guide/eigrpstb.html#wp1021949
CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 400-101 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written v5.0 exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written v5.0 exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written v5.0 exam dumps will help you to be the Cisco specialist, clear your 400-101 exam and get the final success.
400-101 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing
400-101 Cisco exam dumps (100% Pass Guaranteed) from CertBus: https://www.certgod.com/400-101.html [100% Exam Pass Guaranteed]
Why select/choose CertBus?
Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.
 |  |  |  |  | |
|---|---|---|---|---|---|
 |  | | |  | |
| Brand | Certbus | Testking | Pass4sure | Actualtests | Others |
| Price | $45.99 | $124.99 | $125.99 | $189 | $69.99-99.99 |
| Up-to-Date Dumps |  |  | | | |
| Free 365 Days Update | | | | | |
| Real Questions | | | | | |
| Printable PDF | | | | | |
| Test Engine | | | | | |
| One Time Purchase | | | | | |
| Instant Download | | | | | |
| Unlimited Install | | | | | |
| 100% Pass Guarantee | | | | | |
| 100% Money Back | | | | | |
| Secure Payment | | | | | |
| Privacy Protection | | | | | |