As a leading IT exam study material provider, CertBus not only provides you the 350-001 exam questions and answers but also the most comprehensive knowledge of the whole 350-001 CCIE Routing and Switching Written certifications. We provide our users with the most accurate 350-001 CCIE Routing and Switching Written study material about the 350-001 exam and the guarantee of pass. We assist you to get well prepared for 350-001 certification which is regarded valuable the IT sector.
We CertBus has our own expert team. They selected and published the latest 350-001 preparation materials from Cisco Official Exam-Center: http://www.certgod.com/350-001.html
QUESTION NO:22
Refer to the exhibit.
Which path is selected as best path?
A. path 1, because it is learned from IGP B.
path 1, because the metric is the lowest C.
path 2, because it is external
D. path 2, because it has the higher router ID
Answer: B
Explanation:
QUESTION NO:25
Refer to the exhibit.
After a link flap in the network, which two EIGRP neighbors will not be queried for alternative
paths? (Choose two.)
A. 192.168.1.1
B. 192.168.3.7
C. 192.168.3.8
D. 192.168.3.6
E. 192.168.2.1
F. 192.168.3.9
Answer: B,C
Explanation:
Explanation
Both 192.168.3.7 and 192.168.3.8 are in an EIGRP Stub area
The Enhanced Interior Gateway Routing Protocol (EIGRP) Stub Routing feature improves network
stability, reduces resource utilization, and simplifies stub router configuration.
Stub routing is commonly used in a hub and spoke network topology. In a hub and spoke network,
one or more end (stub) networks are connected to a remote router (the spoke) that is connected to
one or more distribution routers (the hub). The remote router is adjacent only to one or more
distribution routers. The only route for IP traffic to follow into the remote router is through a
distribution router. This type of configuration is commonly used in WAN topologies where the
distribution router is directly connected to a WAN. The distribution router can be connected to
many more remote routers. Often, the distribution router will be connected to 100 or more remote
routers. In a hub and spoke topology, the remote router must forward all nonlocal traffic to a
distribution router, so it becomes unnecessary for the remote router to hold a complete routing
table. Generally, the distribution router need not send anything more than a default route to the
remote router.
When using the EIGRP Stub Routing feature, you need to configure the distribution and remote
routers to use EIGRP, and to configure only the remote router as a stub. Only specified routes are
propagated from the remote (stub) router. The router responds to queries for summaries,
connected routes, redistributed static routes, external routes, and internal routes with the message
“inaccessible.” A router that is configured as a stub will send a special peer information packet to
all neighboring routers to report its status as a stub router. Any neighbor that receives a packet
informing it of the stub status will not query the stub router for any routes, and a router that has a
stub peer will not query that peer. The stub router will depend on the distribution router to send the
proper updates to all peers.
Reference
http://www.cisco.com/en/US/docs/ios/12_0s/feature/guide/eigrpstb.html#wp1021949
QUESTION NO:1
Which two commands are required to enable multicast on a router, knowing that the receivers only
support IGMPv2? (Choose two.)
A. ip pim rp-address
B. ip pim ssm
C. ip pim sparse-mode
D. ip pim passive
Answer: A,C
Explanation:
Sparse mode logic (pull mode) is the opposite of Dense mode logic (push mode), in Dense mode
it is supposed that in every network there is someone who is requesting the multicast traffic so
PIM-DM routers begin by flooding the multicast traffic out of all their interfaces except those from
where a prune message is received to eliminate the
QUESTION NO:35
Which command will define a VRF with name \’CCIE\’ in IPv6?
A. ip vrf CCIE
B. ipv6 vrf CCIE
C. vrf definition CCIE
D. ipv6 vrf definition CCIE
Answer: C
Explanation:
QUESTION NO:24
Refer to the exhibit.
R1 is not learning about the 172.16.10.0 subnet from the BGP neighbor R2 (209.165.202.130).
What can be done so that R1 will learn about this network?
A. Disable auto-summary on R2.
B. Configure an explicit network command for the 172.16.10.0 subnet on R2.
C. Subnet information cannot be passed between IBGP peers.
D. Disable auto-summary on R1.
Answer: B
Explanation:
By default, BGP does not accept subnets redistributed from IGP. To advertise and carry subnet
routes in BGP, use an explicit network command or the no auto-summary command. If you disable
auto-summarization and have not entered a network command, you will not advertise network
routes for networks with subnet routes unless they contain a summary route.
Reference
http://www.cisco.com/en/US/docs/ios/11_3/np1/command/reference/1rbgp.html
QUESTION NO:10
Which command is used to enable EtherChannel hashing for Layer 3 IP and Layer 4 port-based
CEF?
A. mpls ip cef
B. port-channel ip cef
C. mpls ip port-channel cef
D. port-channel load balance
E. mpls ip load-balance
F. ip cef EtherChannel channel-id XOR L4
G. ip cef connection exchange
Answer: D
Explanation:
QUESTION NO:18
Refer to the exhibit.
Which statement is correct about the prefix 160.0.0.0/8?
A. The prefix has encountered a routing loop.
B. The prefix is an aggregate with an as-set.
C. The prefix has been aggregated twice, once in AS 100 and once in AS 200.
D. None of these statements is true.
Answer: B
Explanation:
QUESTION NO:32
Which two tunneling techniques support IPv6 multicasting? (Choose two.)
A. 6to4
B. 6over4
C. ISATAP
D. 6PE
E. GRE
Answer: B,E
Explanation:
When IPv6 multicast is supported (over a 6to4 tunnel), an IPv6 multicast routing protocol must be
used
Restrictions for Implementing IPv6 Multicast
IPv6 multicast for Cisco IOS software uses MLD version 2. This version of MLD is fully backward-
compatible with MLD version 1 (described in RFC 2710). Hosts that support only MLD version 1
will interoperate with a router running MLD version 2. Mixed LANs with both MLD version 1 and
MLD version 2 hosts are likewise supported.
IPv6 multicast is supported only over IPv4 tunnels in Cisco IOS Release 12.3(2)T, Cisco IOS
Release 12.2
(18)S, and Cisco IOS Release 12.0(26)S.
When the bidirectional (bidir) range is used in a network, all routers in that network must be able to
understand the bidirectional range in the bootstrap message (BSM).
IPv6 multicast routing is disabled by default when the ipv6 unicast-routing command is configured.
On Cisco Catalyst 6500 and Cisco 7600 series routers, the ipv6 multicast-routing also must be
enabled in order to use IPv6 unicast routing
Reference http://www.cisco.com/web/about/ac123/ac147/ac174/ac197/
about_cisco_ipj_archive_article09186a00800c830a.html
http://www.cisco.com/en/US/docs/ios/ipv6/configuration/guide/ip6-multicast.html
https://supportforums.cisco.com/thread/183386
QUESTION NO:13
Which two statements are true about traffic shaping? (Choose two.)
A. Out-of-profile packets are queued.
B. It causes TCP retransmits.
C. Marking/remarking is not supported.
D. It does not respond to BECN and ForeSight Messages.
E. It uses a single/two-bucket mechanism for metering.
Answer: A,C
Explanation:
QUESTION NO:5
Refer to the exhibit.
A small enterprise connects its office to two ISPs, using separate T1 links. A static route is used
for the default route, pointing to both interfaces with a different administrative distance, so that one
of the default routes is preferred.
Recently the primary link has been upgraded to a new 10 Mb/s Ethernet link.
After a few weeks, they experienced a failure. The link did not pass traffic, but the primary static
route remained active. They lost their Internet connectivity, even though the backup link was
operating.
Which two possible solutions can be implemented to avoid this situation in the future? (Choose
two.)
A. Implement HSRP link tracking on the branch router R1.
B. Use a track object with an IP SLA probe for the static route on R1.
C. Track the link state of the Ethernet link using a track object on R1.
D. Use a routing protocol between R1 and the upstream ISP.
Answer: B,D
Explanation:
Interface Tracking
Interface tracking allows you to specify another interface on the router for the HSRP process to
monitor in order to alter the HSRP priority for a given group.
If the specified interface\’s line protocol goes down, the HSRP priority of this router is reduced,
allowing another HSRP router with higher priority can become active (if it has preemption
enabled).
To configure HSRP interface tracking, use the standby [group] track interface [priority] command.
When multiple tracked interfaces are down, the priority is reduced by a cumulative amount. If you
explicitly set the decrement value, then the value is decreased by that amount if that interface is
down, and decrements are cumulative. If you do not set an explicit decrement value, then the
value is decreased by 10 for each interface that goes down, and decrements are cumulative.
The following example uses the following configuration, with the default decrement value of 10.
Note: When an HSRP group number is not specified, the default group number is group 0.
interface ethernet0
ip address 10.1.1.1 255.255.255.0
standby ip 10.1.1.3
standby priority 110
standby track serial0
standby track serial1
The HSRP behavior with this configuration is:
0 interfaces down = no decrease (priority is 110)
1 interface down = decrease by 10 (priority becomes100)
2 interfaces down = decrease by 10 (priority becomes 90)
Reference
http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a91.shtml#i
ntracking
CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 350-001 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written exam dumps will help you to be the Cisco specialist, clear your 350-001 exam and get the final success.
350-001 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mUVBtM1piOS1IMEU/view?usp=sharing
350-001 Cisco exam dumps (100% Pass Guaranteed) from CertBus: http://www.certgod.com/350-001.html [100% Exam Pass Guaranteed]
Why select/choose CertBus?
Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.